| |
Master's Grade
Japanese Wood Handled Carving Tools
Hand forged laminated 'white steel' blades, expertly tempered
for a long lasting edge. Japanese Red Oak handles. Each blade is
fully sharpened to near razor sharp. These sturdy, handsome, high
quality gravers (also called gouges) are what the old masters use
for carving jin and shari. Made in Japan. |
| |
|
|
| |
|
TBK20506
Branch Lever
13"
$38.00
SALE $28 |
|
|
|
 |
| |
AutoMac Japanese
Power Wood Carver
Expand your
bonsai horizons by leaps and bounds. This is the top of the
line handheld power impact carving tool and is the choice
of Japanese professional bonsai artists and woodworkers.
It delivers up to 10,000 impacts per minute. It is capable
of both very heavy and very delicate cuts and can therefore
be used for the most refined jin and shari as well as
roughing out larger jobs. Weighs two pounds. The following
five cutters are standard: 1/4" straight chisel, 1/2"
#5 gouge, 1/4" #5 gouge, 3/8" 90 degree V-parting
tool, 1/4" #5 bent gouge. |
T-AM
$299.00
Not Elegable for 40% Off Tool Sale
|
|
| |
|
| |
| |
 |
Flexcut Hand Made
Bonsai Graving Tools
Everyone we've
talked to who uses these US made gravers loves them. Handmade of high quality spring steel. The flexibility of the shaft
helps maintain optimal cutting angles while the hardness of the
blade makes for maximum sharpness and cutting efficiency. Ash handles. |
Tools include four palm gouges each 5.25"
in length: 5/16" gouge, 1/2" skew gouge, 1/8" V
gouge, 3/8" V gouge.Two knives: 1.75" x 7"
straight knife, 1" x 8" draw knife.
7" Straight knife $24
Boxed
set of Six $145 |
|
| |
| |
 |
| |
Jin Pliers
Jin Pliers are used to crush and strip
bark and wood when creating jin and shari (dead branches
and driftwood). Though it is possible to use straight wiring
pliers for jin and shari, pliers that have been de-signed for the task at hand will yield the best results. |
| |
T-27201
Professional Jin Pliers 7"
$45.00 |
|
|
T-024
Master's Stainless Jin Pliers 7"
$85.00 |
|
|
T-025
Master's Stainless Jin Pliers 8"
$95.00 |
|
|
| |
|
 |
| |
Branch Benders
Got a pesky little curve in a formal upright
that you can't correct with just wire? Or a stiff old
section that needs a little movement? Try a branch bender.
After you put it on, tighten the jack screw a little bit every
few days until you get the results you are looking for. Be
sure to leave it on long enough for the branch or trunk to
set in its new position (if you use it with wire you may be
able to remove it sooner). Steel with brass jack screw. Hooks
and jacks are coated with vinyl to help protect trunks and
branches (some people use additional protective padding).
|
| |
T-27433
Small 2.5" x 2.5"
$12.95 |
|
|
T-27432
Medium 3" x 4"
(max branch diameter .75")
$15.95 |
|
|
T-27431
Large 4" x 5"
(max. branch diameter 1.25")
$17.50 |
|
|
T-27430
Extra-large 7" x 7"
(max branch diameter 1.5")
$35.00 |
|
|
| |
|
|
